SOLD! Budbuilt IFS Skid Plate/Bellypan Combo - fits 88-95 V6-Auto Truck/4Runner

[Cebby]

BEEEEEF!

Excellent workmanship as with all Budbuilt products.

These have never been installed and have been in my garage for what seems like forever. I can't use the bellypan since I'm making a custom crossmember for my powertrain swap. Selling as a set. These parts were powdercoated locally, so they are no longer raw steel!

The bellypan requires using Bud's low profile crossmember (mine is sold). Save money and help me get this out of my garage! (minor scratches from moving around and tripping over them) Comes with whatever hardware Bud sent me.

Shipping - East Coast - roughly $50, West Coast roughly $75.

Skid plate - 53 lbs.
Bellypan - 29 lbs.

SOLD AS A SET ONLY! First $400 + shipping.

And now some pics...

http://rigs.corequipment.com/Cebby/forsale/skid_bellypan%20003%20(Medium).jpg

http://rigs.corequipment.com/Cebby/forsale/skid_bellypan%20006%20(Medium).jpg

http://rigs.corequipment.com/Cebby/forsale/skid_bellypan%20007%20(Medium).jpg

Underside of the Skid:
http://rigs.corequipment.com/Cebby/forsale/skid_bellypan%20001%20(Medium).jpg

Underside of the Bellypan:
http://rigs.corequipment.com/Cebby/forsale/skid_bellypan%20009%20(Medium).jpg

[Cebby]

OK - these are no longer pending sale, so these are available to anyone...

I want these things gone, so now is your chance for a killer deal! They are all boxed up and ready to go. I will now do this set for $400 SHIPPED in the Continental US.

Brand new and powdercoated. You will NEVER find this good of a deal on these anywhere!

[Lee]

ill post it on my club board :)

[Cebby]

ill post it on my club board :)


Thanks Lee!!

[Cebby]

Bump for a killer deal!!

[Cebby]

PRICE DROPPED TO $350 SHIPPED

[Marc P]

Thats a great deal for someone...maybe I should put my IFS back on!!

Somebody better jump on this deal

[Osiris]

If I wait 'til tomorrow, will it go down another $50???? That would make me lean that much more to sending you a certified check. That would save you $9 in paypal fees.

How will they bolt up to my currently stocker '95 4Runner. Little by little I may add a thing or two.

Osiris

[Cebby]

Meet me in the middle (another $25 drop) and they are yours. I'm already getting crushed on this sale. Where ya at?

The skid will bolt up as is, bolting up the bellypan will require the addition of a BudBuilt (http://www.budbuilt.com) low profile crossmember.

[Osiris]

Oh h3ll. gotta buy something else, eh??? Shouldn't have sold that to MarkP! :)
I take it I will need the dual case crossmember? I have a '95 4Runner 4WD w/3.0
Dang, that's another $260+

Is there a rear skid plate also? Or are there only the front skid plate and belly pan? What about the rear shaft and exhaust protection ?

I know that is what you have, but do I need to get a rear skid plate?

[amgraham]

Oh h3ll. gotta buy something else, eh??? Shouldn't have sold that to MarkP! :)
I take it I will need the dual case crossmember? I have a '95 4Runner 4WD w/3.0
Dang, that's another $260+

Is there a rear skid plate also? Or are there only the front skid plate and belly pan? What about the rear shaft and exhaust protection ?

I know that is what you have, but do I need to get a rear skid plate?


You don't need a dual case crossmember unless you plan to run duals. A single works fine with the belly pan. Those prices come with the crossmember skid but I bet you could call Bud and tell him that you're getting Cebby's belly pan and he would probably sell you the crossmember cheaper without the little skid. He's a super nice guy to talk to and normally willing to help.

Also, there is no driveshaft/exhaust protection that I know of.. On mine the gas tank gets hit well before the driveshaft or exhaust.

For reference here is the bottom of my truck with the same setup, just the 4 cyl version (the belly pan is slightly different):
http://www.amgraham.com/photogallery/DSC05754-800X600.JPG

[Marc P]

Oh h3ll. gotta buy something else, eh??? Shouldn't have sold that to MarkP! :)
I take it I will need the dual case crossmember? I have a '95 4Runner 4WD w/3.0
Dang, that's another $260+







You snoozed....I would have bought the whole setup if my IFS didnt fall off. :flipoff:

[Osiris]

Oh h3ll. gotta buy something else, eh??? Shouldn't have sold that to MarkP! :)
I take it I will need the dual case crossmember? I have a '95 4Runner 4WD w/3.0
Dang, that's another $260+

Is there a rear skid plate also? Or are there only the front skid plate and belly pan? What about the rear shaft and exhaust protection ?

I know that is what you have, but do I need to get a rear skid plate?


You don't need a dual case crossmember unless you plan to run duals. A single works fine with the belly pan. Those prices come with the crossmember skid but I bet you could call Bud and tell him that you're getting Cebby's belly pan and he would probably sell you the crossmember cheaper without the little skid. He's a super nice guy to talk to and normally willing to help.

Also, there is no driveshaft/exhaust protection that I know of.. On mine the gas tank gets hit well before the driveshaft or exhaust.

For reference here is the bottom of my truck with the same setup, just the 4 cyl version (the belly pan is slightly different):
http://www.amgraham.com/photogallery/DSC05754-800X600.JPG


Ok. so the skid goes from front bumper to IFS and the belly pan goes from IFS to end of tranny/trfr case w/X-member at that point?

I thought dual meant tranny + transfer case for 4X4 and single was for 2WD set up. Tell me what "duals" means. Thx.

[Osiris]

Oh h3ll. gotta buy something else, eh??? Shouldn't have sold that to MarkP! :)
I take it I will need the dual case crossmember? I have a '95 4Runner 4WD w/3.0
Dang, that's another $260+



You snoozed....I would have bought the whole setup if my IFS didnt fall off. :flipoff:


suck @ss :gay: :booya:

;)

[Cebby]

Single is for one transfer case. Duals is for two - also referred to as a doubler. There are a few triple setups out there too.

http://www.marlincrawler.com/htm/transfercase/pickup_dual.htm

[amgraham]

Yup. If you run two cases you essentially bolt another one on the back of your current case (not quite that simple but you get the idea).

Here is a pics of how far the belly pan comes back on mine (to the rear of the t-case):
http://www.amgraham.com/photogallery/DSC05753-800X600.JPG

[Cebby]

OK - new price is $325 shipped. If I don't get a commitment for this over the weekend, it goes on eBay on Monday. Price will likely start at $325 on eBay.

[Cebby]

SOLD!!