Buildup of Jimbo74's Xcab

[jimbo74]

this thread is a continuation of my garage thread found here:

http://www.ultimateyota.com/index.php?option=com_smf&Itemid=26&topic=794.0

in this thread, issues and comments will be addressed

[reggie 00]

Go to a welding supply. and if you cant find 2G go "0". At the welding supply shop it will probably be cheaper than at your local stereo shop, but it wont be in pretty colors, most likely just black.

And don't tell my buddy (who owns the local stereo shop) that i sent you to a welding supply instead.

[olharleyman]

I agree go to the welding supple shop and you will be very happy in the end with the better wire.

[jimbo74]

new pics!!!!

OK here is the exhaust..... i usually run it like this (open) i hate my neighbors ;) and like the way it sounds
http://www.explorerforum.com/photopost/data/3550/cat.jpg

here is the muffler, it is sleeved so it slips on to the rest, and it has a clamp to make it legal or hush it up a little bit
http://www.explorerforum.com/photopost/data/3550/muffler.jpg



and here is a pic from the front, none of that is bolted in just ziptied in place for the picture....

http://www.explorerforum.com/photopost/data/3550/front5.jpg




ENGINE IS IN!!! AND CONNECTED TO TRANNY!!!!!! now i just need to bolt it all down

[SacRunner]

i wanted to run 2 guage, but have been unable to find anything automotive in that size. does everyone think that 4 guage is sufficient? it is at least as good as stock, and its not 23+ years old either


If you really see a need or just a desire to run 2ga and cant find it easily, why not just run 2 lengths of the 4ga?

[jimbo74]

Engine in! RAWR!!!!!
http://www.explorerforum.com/photopost/data/3550/Picture_93.jpg

used 35x14.5x15 thornbirds
http://www.explorerforum.com/photopost/data/3550/Picture_213.jpghttp://www.explorerforum.com/photopost/data/3550/Picture_124.jpghttp://www.explorerforum.com/photopost/data/3550/Picture_142.jpghttp://www.explorerforum.com/photopost/data/3550/Picture_132.jpg

2wd rear springs with aal
http://www.explorerforum.com/photopost/data/3550/Picture_411.jpg

harbor freight electric impact
http://www.explorerforum.com/photopost/data/3550/Picture_54.jpg

random garage/truck pic
http://www.explorerforum.com/photopost/data/3550/Picture_104.jpg

[jimbo74]

http://www.explorerforum.com/photopost/data/3550/medium/lightpulleys.jpg

http://www.explorerforum.com/photopost/data/500/medium/lightpulleys1.jpg

[jimbo74]

well, the build has been halted until after the wedding...... i dont have the time or the $ to do anything....


on a side note....

i might be getting a new truck, it runs but the CEL comes on everyday--my parents dont wnat to deal with getting it smogged and reregistering it, its current until the end of august

It’s a 96 xlt 4x4 explorer 4dr, its been In the family since at least 98, was bought used from a realtor (my dad’s bosses wife @ the time) that upgraded. Leather interior, truck now has a lot of mileage, heads and upper end rebuilt @ 110k because my mom overheated it and cracked the heads…. 3.73 LSD d4, 8.8 c-clip rear end 31 spline axles with disc brakes, pushbutton 4x4 (well rotary switch on dash) good condition 235/75/15 bridgestone dueler, not the at, but hl I think is the model. Tranny went out and was replaced once. My dad said it slipped once on him after the rebuild but has been fine since…. The 4x4 works sporadically…. A/c is still cold, heater still blows hot. CEL triggers almost everyday. Truck needs to be smogged to be registered

Truck has all the options, power doors, alarm, windows… my mom decided to try and pass a bobtail, that wasn’t stopped and the rear door is crunched, but it didn’t touch the fenders or anything, door still opens and window still rolls up and down. Dings here and there, but it is 12 years old

it said o2 bad, we replaced the 02, code came back, we think it’s the cat now, as truck does have a bit of mileage on it. I think there are 3 o2 sensors on the truck… I might just replace all the sensors and the cat. Shouldn’t cost too much….

[jimbo74]

http://www.explorerforum.com/photopost/data/500/newfront1.jpg

[jimbo74]

didnt get it running, but it is seriously close, we got the starter wire hooked up, fan clutch in, radiator in, got it filled, res tanks in, bolted stuff on the walls down, dizzy in, oil in

all that is left is drain the tank, refill with new gas, new gas filter, and find my spark plug wires where they are, and try to start it up....

oh yeah, and i need to charge the battery, its been dead so long, it jsut stays at like 8 volts, enough to run lights and hte horn, but it wont come close to starting, ill probably need to jump it....


rob! do you have an extra set of wires?


then we need to change out all the fluids, tranny, diffs, tcase, and bleed the brakes again, i also have an eclip i need to put on the ebrake cable... install seats, put the door back on, put in a seatbelt, and find some body mounts and bolts for the bed, tailgate, lights

swap out rims, have some tires with chrome d windows

[jimbo74]

got a little bit of work done, but cant get it to turn over... i have power at the battery and to the starter, but when i turn the key in the ignition, the little wire gets no voltage to the starter... hmmmmmm looks like i have an ignition switch or wiring problem

[jimbo74]

http://www.explorerforum.com/photopost/data/500/pic010708_1.jpg


which lights? the round in the grill guard or the restangle? i also plan on going with 7" rounds on the top side of the grille guard, will end up sitting jsut atthe hoodline... probably should go all rounds....

all round?

might also mount some yellow foglights right new to the headlights for turn signals

[jimbo74]

its been awhile since i psoted here..... my truck runs!!!!!! been driving it around until last friday :( but only a temporary setback right now.... one of my water neck bolt holes is stripped and i need to helicoil it, good thing i found out befroe catastrophic failure happened.. i was at costco and saw steam! was liek wtf?! parked it and checked it out, went in costco and bought some tools and coolant... bandaided it home... now just need to helicoil it... already bought the helicoil

it has all its body parts now, i just dont have newer pics

http://www.explorerforum.com/photopost/data/3550/pic052308_5.jpg
http://www.explorerforum.com/photopost/data/3550/pic052308_6.jpg
http://www.explorerforum.com/photopost/data/3550/pic052308_4.jpg
http://www.explorerforum.com/photopost/data/3550/pic052308_2.jpg
http://www.explorerforum.com/photopost/data/3550/pic052308_1.jpg
http://www.explorerforum.com/photopost/data/3550/lights5.jpg
http://www.explorerforum.com/photopost/data/3550/airsilencer.jpg
http://www.explorerforum.com/photopost/data/3550/pic051808_6.jpg

[jimbo74]

helicoiled my waterneck, seems to be good... havent road tested it yet, but i did bench test it