1998 4Runner Suspension Rebuild and Rust Mitigation!

[mastacox]

Many of you may be aware that 3rd gen 4Runners have a hit or miss reputation for frame rust, especially in the rear of the vehicle. Unlike Tacomas of the same era, Toyota chose not to do a factory recall and repair for frame rust on these vehicles. With that in mind, when the COVID-19 pandemic rolled around in spring of 2020 I decided I wanted to do a bit of work under the 4Runner to update worn components in the front suspension. Since that apparently wasn't enough of a project I also chose to do a full "rust mitigation treatment" of my 4Runner's frame to ensure it survives for another 20 years.

Since I completed this project a couple months ago, I thought it might be fun to document it for others to see. Here goes!

Step 1: Inspecting the front suspension


Things look pretty worn, time to get a rebuild done!
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200216_222555-768x1024.jpg

Disassemble front suspension and take steering knuckles to shop to press out old hardware. They're gross at over 230,000 miles!
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200328_172130-768x1024.jpg


The knuckles had rusted enough I wanted to do something to fix them up. A bolt broke on disassembly too, had to drill and tap the hole.
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200328_172134-768x1024.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200328_183741-768x576.jpg


I'm bored and it's COVID times, lets build an electrolysis tank to clean them up! Hacked up an 18V laptop power supply, used some cut up steel cans for the anodes, and Super Washing Soda for the electrolyte solution. The washing soda is Sodium Carbonate, not Sodium Bicarboante
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200328_200412-768x576.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200330_092030-768x1024.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200329_091259-768x576.jpg


They look a lot better after the electrolysis tank, but they're not done yet.
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200329_214948-768x1024.jpg

After a couple wire wheels and lots of cordless drill batteries, we're on the right track. Ready for paint:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200330_131243-768x1024.jpg

http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200330_131250-768x1024.jpg


Cleaned with brake cleaner, and then masked off the interior areas and gave them a coat of Rustoleum Protective Enamel. NOW we're looking good again!
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200330_155416-768x1024.jpg


Repainted the brake disc covers and took everything back to the shop and got all new parts pressed in. Ready for re-install!
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200404_121138-768x576.jpg


Continued in following posts, lots left to go...

[4x4mike]

Wow, those turned out nice! Great job.

[mastacox]

Step 2: De-Rust The Rear Suspension and Axle!

This is where things got a little messy. Over the years of wet roads and intermittent snow in New Mexico, the 4Runner had developed surface rust in several unsavory areas. I've seen far worse cases to be sure, but it was getting to a level I was uncomfortable with and wanted to address. So I had to dive in and since the front end was pulled apart anyway, I figured why not put the whole thing on jack stands and pull apart the rear too!

What I was dealing with. Surface rust along seams and on much of the rear axle and underbody cross members. Sharp eyes will also see the TRD muffler is rusted out, I replaced the catalytic converter and whole cat-back exhaust with a bolt-in system from Borla.
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200216_222545-768x1024.jpg

Spent a good amount of time wire wheeling the hardware with my bench grinder. Saved me a lot on new hardware and much of the "key" stuff in the front end (castle nuts, etc.) came with the new ball joints, brake calipers, or other hardware purchased for re-install:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200401_191510-768x576.jpg

After much grunting, groaning, and fighting, I was able to carefully remove everything from the rear suspension. I do mean everything!
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200420_223547-768x576.jpg

I skipped over it last post but I decided I wanted to replace the upper and lower control arms up front, rebuilding the old ones would be as much or more than buying new. Thing is, anyone with experience with these control arms knows the lowers can be a disaster if the alignment adjusters are stuck. Guess what?
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200403_190812-768x576.jpg

Mine were stuck bad, and no matter how much I hammered they wouldn't come out. SO good news is I didn't care about sawing them up and went to town with a sawzall and determination:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200403_190924-768x1024.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200403_194952-768x576.jpg

With the front fully disassembled (or close enough to it) I concentrated on the rear axle which had been fully removed:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200422_173145-768x576.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200422_173152-768x1024.jpg

With the axle fully removed, I was able to address surface rust in a lot of key areas that couldn't be reached while on the truck, like the spring mounts:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200422_173211-768x1024.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200422_173215-768x1024.jpg

After a lot more wire wheels and batteries, I had a halfway decent axle housing ready for paint:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200422_184609-768x576.jpg

Much of the factory finish was lost in some areas, but in other places it remained. I ground everything I could while maintaining the factory finish, cleaned the whole axle with brake cleaner, masked the internal areas, and then went to town with a 1-2 punch of Rustoleum Rust Reformer and Rustoleum Protective Enamel:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200423_123501-768x1024.jpg

Coat 1 (Rust Reformer):
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200422_192812-768x576.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200422_192818-768x576.jpg

Coat 2 (Protective Enamel):
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200423_181529-768x1024.jpg

Since I had them out and was keeping all of the rear links as-is for now (had to draw the line somewhere for budget reasons), I wire wheeled and painted the rear links as well for a rust-free, protected finish:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200422_195247-768x576.jpg

To be continued...

[mastacox]

Step 3: Differential Love <3

It's a 4runner, it's in pieces in my garage. What's a guy to do? Clean and paint differentials of course!

Rear diff, after wire wheeling. Surface rust mostly dealt with but still some light oxidation:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200423_110651-768x1024.jpg

Nothing the Rustoleum Rust Reformer can't handle:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200423_114341-768x1024.jpg

...and of course the cursory Protective Enamel as well:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200423_123106-768x1024.jpg

E-locker motor and skid plate got a quick coat too:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200423_160216-768x1024.jpg

The front diff was a bigger mess, as it had been leaking oil from its outer seal. Coated in a grimy coat of oil and dirt:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200502_122403-768x576.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200502_122354-768x576.jpg

I removed all hoses and wiring, cleaned up the diff, replaced the outer seals, and then went to town with the old wire wheel. Cleaned with brake cleaner, and then zapped with Rust Reformer:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200502_133303-768x1024.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200502_133309-768x1024.jpg

To be continued...

[mastacox]

The Parts Pile...

All of this disassembly and chaos, where does it end?? Well, I was also collecting my grand plan vision for re-assembly, and it involved around $6,000 in parts.

This included:
- New front wheel bearings with seals, etc.
- Upper and lower control arms, upper and lower ball joints, and new alignment cams since I sawed the old ones in half
- CV Shafts, both sides
- Brake rotors, drums, calipers, pads, rebuild kits, brake lines
- New front and rear sway bar end links, brackets, and bushings
- Borla exhaust and direct-fit catalytic converter with second O2 sensor bung
- Rear Toytec 3" lift springs to replace the tired factory springs that had been on lift spacers for about 150,000 miles
- Rear 3" lift Rancho 9000 shocks
- New RCI 3/16" powder coated front skid plate
- New ABS sensors and wiring harnesses for all 4 corners
- Refinished and powder-coated wheels (17" FJ Cruiser Alloys) with 285x70r17 BFG All Terrain KO2

The parts pile in its mostly complete state:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200403_114342-768x576.jpg

New Calipers:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200404_135051-768x576.jpg

Obnoxious slotted brake rotors from EBC:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200403_112521-768x1024.jpg

Pre-bent ready to bolt in Borla exhaust:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200402_141948-768x1024.jpg

Sand blasted and powder coated wheels:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200512_143819-768x576.jpg

BFG All Terrains:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200529_143303-2-768x576.jpg

And my secret weapon to prevent future frame rust:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200903_171504-768x1024.jpg

To be continued...

[mastacox]

Step 4: Re-assembly!

I had been taking apart and cleaning/painting parts for months now, time to start bolting stuff back together. Before that though, one last step- rust work on the undercarriage!

I basically laid under the 4Runner with a creeper, safety goggles, and a cordless drill with wire wheel. I ground anywhere I found even a little rust. I even pulled the gas tank and did it too (I had to install a new fuel pump anyway).

Cleaned up front end frame ready for paint. I used Rustoleum Rust Reformer pretty much everywhere, and then for good measure I taped up all the holes in the frame and used Eastwood Internal Frame Coating to seal up anything going on inside the frame:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200425_2222372-768x576.jpg

I didn't take a lot of pictures of the rear during, because I was focused on the task at hand. Here you can see part of the end result though (don't worry I used Rust Reformer on the e-brake hardware too):
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200528_100417-768x576.jpg

Starting re-assembly on the front end:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200524_102221-768x1024.jpg

New upper control arms, ball joints, everything:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200528_100357-768x576.jpg

Shiny new parts everywhere!
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200524_114032-768x1024.jpg

Almost done:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200528_190219-768x1024.jpg

A before and after shot really shows the difference:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200529_001210-COLLAGE.jpg

Putting the rear back together I had some stud break, so I got fancy new ones from ARP:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200529_132200-768x576.jpg

Side by side of an old stud and a new one:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200529_130543-768x1024.jpg

The rear brakes were pretty gross, gotta clean them up:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200529_1808212-768x845.jpg

Cleaned and painted rear brakes, and then installed new hardware with rebuild kit:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200529_191244-768x1024.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200529_2046222-768x1067.jpg

Throwing sparks to trim the new lugs on the front, to work with my custom wheel spacers:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200530_200740-768x1024.jpg

Assembly Complete front and rear!
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200530_221058-768x1024.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200530_221047-768x1024.jpg

[4x4mike]

Great job on the re-fresh. That thing is ready for another lifetime of miles.

[mastacox]

Step 5: Tidying Up

Getting very close to the finish line and I had a trip to Austin in 2 days, so I had to rush things a bit... Still, I've got a couple pictures of things going on. Mainly, I had to get the driveshafts and exhaust in, mount the gas tank skid plate, and then lay down a new coat of rust protectant to ensure anything I might have missed would get locked in place.

First, gotta try on the new shoes and then start torquing down the bolt in the suspension. You have to torque them when the vehicle's sitting at ride height on level ground:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200604_203325-768x1024.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200604_203320-768x1024.jpg

Next I had to get the fuel system in order, I installed a new fuel pump in the tank, new fuel filter, and new injectors. This took care of several issues and cleaned things up a good bit. The new fuel injectors are from a Five O Motorsport, and are the exact same size as factory but flow at 330cc and are flow tested to all match:
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200302_172655-768x576.jpg
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200604_214323-768x1024.jpg

One trick I wish I'd known about a long time ago is wax-based metal protectant. I sprayed this stuff on everything underneath the truck (except the brakes). It would have saved me a lot of work if I'd started using it about 15 years ago!
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200903_171716-768x1024.jpg

Fired up the 4Runner at about 3am and it drives! Took it to get an alignment, ready for another couple of decades of adventures! (Don't worry I did put the gas tank skid plate back on, but you can see even it got a fresh coat!) 3 more years and it qualifies for classic car plates!!!

DONE
http://pictures.strikeforceniner.com/wp-content/uploads/2020/09/20200605_093413-2-768x576.jpg

[Bob98SR5]

Holy shizzle! How long did that take, Brian? Excellent work as always.

[mastacox]

Hey Bob! Start to finish it took me about 3 months, mainly working random weekends and nights here and there. If I had to guess I think it was about 120-150 hours of work, but I took my time and did everything as perfect as possible (while still making progress).

[paddlenbike]

This has been a satisfying thread to read. Nice job!

[mastacox]

Thanks man, it was a lot of work start-to-finish, but totally worth it. Putting the sway bars back on was one of the biggest changes for me; yes off-road performance is better without them but with the number of miles put on the highway it's really a relief to have reasonable body sway again.

[fenrisx]

Nice work, Brian!

I recently put front sway bar end links back on my 4Runner (been about 11 years without them) and was surprised at how noticeable the difference was... and that's even with me running the stiff (imo) PP 1" lift springs.