Search:

Type: Posts; User: Bob98SR5; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds; generated 59 minute(s) ago.

  1. Replies
    0
    Views
    1,002

    WTB - $10K-ish Toyota truck

    Anyone selling? Asking for my boss's daughter in Denton, TX. Contact me at bobyongkim@gmail.com
  2. Replies
    9
    Views
    17,338

    Hi team, I'll be moving out in about 3 weeks....

    Hi team,

    I'll be moving out in about 3 weeks. If anyone here in Nor Cal wants to finish this project, please let me know asap @ bobyongkim@gmail.com. I'll give you all the metal and nearly...
  3. Replies
    8
    Views
    2,306

    FINAL STEPS Re-install the headlamps by first...

    FINAL STEPS
    Re-install the headlamps by first attach attaching the harnesses and then bolting down the headlamp assemblies. Pro-tip on the driver's side: before completely tightening down the...
  4. Replies
    8
    Views
    2,306

    AIMING THE HEADLIGHTS If you followed my very...

    AIMING THE HEADLIGHTS
    If you followed my very first step above, this should be very easy. Adjusting the nuts are as follows:

    Vertical beam adjustment nuts are very easy to access for both sides....
  5. Replies
    8
    Views
    2,306

    HARNESS ASSEMBLY, WIRE ROUTING, and POS/NEGATIVE...

    HARNESS ASSEMBLY, WIRE ROUTING, and POS/NEGATIVE WIRING
    The harness comes in two parts. Connect them together. It should be very obvious and mechanically the two male/female connectors that adjoin...
  6. Replies
    8
    Views
    2,306

    INSTALL PROJECTOR BULBS W/ SILICONE GASKET, LOCK...

    INSTALL PROJECTOR BULBS W/ SILICONE GASKET, LOCK RING, AND BUTTERFLY NUT
    OK, this is the easiest part but pay attention to which way the fan on the projector bulb is oriented. The fan must be facing...
  7. Replies
    8
    Views
    2,306

    GLASS REMOVAL AND BUTYL REMOVAL Pro tip: Clear a...

    GLASS REMOVAL AND BUTYL REMOVAL
    Pro tip: Clear a large workspace. Sorry no pics for this step.

    Begin by unclipping the 4 metal retaining clips with a flat bladed screw driver by gently prying...
  8. Replies
    8
    Views
    2,306

    REMOVE PARTS FROM GREY HEADLIGHT HOUSING Again...

    REMOVE PARTS FROM GREY HEADLIGHT HOUSING
    Again take a photo of the back of the housing so that you have a reference for the orientation of the hoses when you put everything back together.

    Begin...
  9. Replies
    8
    Views
    2,306

    REMOVING REAR BLACK HOUSING Have your phone’s...

    REMOVING REAR BLACK HOUSING
    Have your phone’s camera ready to take pics of what you’re removing and especially the height of the threads in relation to the top of the beam adjustment nuts. If you...
  10. Replies
    8
    Views
    2,306

    SIDE MARKERS REMOVAL Remove the single Philip...

    SIDE MARKERS REMOVAL
    Remove the single Philip head screw at the top of the marker end inside the engine bay. Set aside for now but don’t forget to screw it back in. Pop out by hitting the rear...
  11. Replies
    8
    Views
    2,306

    Bi-LED projector retrofit project

    I finally got with the times and installed Bi-LED projectors from a company named BX Built. I just purchased the projector kit only, not the ready-to-bolt on kit that seems to be taking the company a...
  12. Replies
    9
    Views
    17,338

    Too high, too low

    Utilizing the stock holes, if I use one set it's too high. If I use a bottom set of holes, the bottom of the shelving system hits the horizontal metal. So what I did was drill new holes in the vert...
  13. Replies
    9
    Views
    17,338

    More pics

    Here's some shots of the seal sealed drawer and all those darn little rubber nubs that needed to be cut off. I lost count.
  14. Replies
    9
    Views
    17,338

    Damnit, my whole post got timed out and lost. ...

    Damnit, my whole post got timed out and lost.

    Ok so here's the short story:

    - I used one of the largest pieces of sheet metal (thinner gauge) as the drawer pan. This required a little...
  15. Replies
    9
    Views
    17,338

    Mike, The main goal is to build a lockable...

    Mike,

    The main goal is to build a lockable cargo box. I do though have an idea/concept of building sliding arms that are welded to the side of box that will serve as the frame for a sleeping...
  16. Holy shizzle! How long did that take, Brian? ...

    Holy shizzle! How long did that take, Brian? Excellent work as always.
  17. Ken, Yup, half fairing, no light. As I...

    Ken,

    Yup, half fairing, no light. As I understand it, all you need to do is to break up the air flow that goes up and over the fairing. I may clip some large binder clips up there to experiment.
  18. Replies
    9
    Views
    17,338

    If you're an old fart like me, you might've had...

    If you're an old fart like me, you might've had either Lincoln Logs and/or Erector Set growing up. This is just like an Erector Set. Just nuts and bolts. So after cutting my vert supports, I...
  19. Replies
    9
    Views
    17,338

    Looking at other designs and having slept in the...

    Looking at other designs and having slept in the back of my 4runner a few times on a wood platform, I know from experience that you don't want to make this box too high else you feel like you're...
  20. Replies
    9
    Views
    17,338

    The Adrian Steel boxes are widely used by people...

    The Adrian Steel boxes are widely used by people with cargo vans. They are a US based company in MI, so that's a good thing. The thing I purchased had two types of inserts in the slide out drawers....
  21. Replies
    9
    Views
    17,338

    The Adrian Steel Cargo Box project

    Gents,

    I've always wanted to build a cargo box to keep things safe and secure when traveling esp with pew pews. Also I've always wanted to build a cargo box that would also be capable of...
  22. Ken, I haven't worked on the rack since I...

    Ken,

    I haven't worked on the rack since I installed it. Too many other projects. One thing I will say though is that this rack is loud on the highway. I hit 70 mph and this thing whistles. I...
  23. After looking at my truck from behind, I realized...

    After looking at my truck from behind, I realized that the driver's side brake light is partially obscured by the tire carrier (despite what the mfg says). So for safety's sake, I decided to finally...
  24. Some outdoor shots

    Some outdoor shots
  25. Since the holes on the other side are unused (for...

    Since the holes on the other side are unused (for now at least), I decided to buy some socket bolts to close up the holes and paint them to match.

    Oh, I also added some essential trail and...
Results 1 to 25 of 498
Page 1 of 20 1 2 3 4