I hope so too. if they go south in a month of use I'm going to throw them in a river lol
I hope so too. if they go south in a month of use I'm going to throw them in a river lol
It would probably be more fun to charge them with propane and gasoline then take them out to the desert and place them down range. Then maybe a Youtube video titled something along the lines of 'the only thing these shocks are good for'.
just an update on the rear 2.0" x 12 smooth bodies I bought. Short story they both leak...
-one leaks from the shaft seal and weeps on the end caps of the reservoir
-the other leaks from the reservoir ends and weeps from the shaft seal
I knew I was in for bad luck with I found about a teaspoon of oil had leaked from one reservoir onto the table over three months. And yes the shocks are and were charged through all the leaking. FOA is just poorly assembled stuff. I have no doubt the parts are fine and I could rebuild them to be leak free, but I wasnt in the market for a "do it yourself" shock kit. Now just as the front shocks (they remain perfect after the factory rebuild by the way), I will have to dick with them sooner then later.
Par for the FOA course it seems. Bummer.
2005 Lexus LX470 - Stock for now...
1998 Toyota 4Runner SR5 V6 4x4 + a bunch of goodies. Lifted, Locked, Illuminated and Armored. Winner,"Best Offroad Truck" - 2010 Pismo Jamboree. It's been upside down and still drives me to work.
yeah I kinda expected it, but crap. Best part is I have no desire to send then to FOA and go through that shit again.
1100 views in 6 months...This is the word of mouth advertising they are reaping
Some videos of common issues:
incorrect oil fill aka slapped together as fast as possible
https://www.youtube.com/watch?v=zR2njURhs8I
end cap not even tightened aka slapped together as fast as possible
https://www.youtube.com/watch?v=B7o3EHlozg4
Main shaft seal bad. aka never tested, just shipped with a prayer.
https://www.youtube.com/watch?v=WISSX4M5EcQ
Granted King shocks are quite a bit more expensive, but look at what they are doing. Take note that each shock is pressurized and left to sit for a few days to make sure there are no leaks. They understand that's a important enough step to make sure their shocks aren't F$%cked on arrival.
https://www.youtube.com/watch?v=7dfB8Lt81y4
https://www.youtube.com/watch?v=7dfB8Lt81y4
Last edited by troyboy162; 09-07-2014 at 01:24 AM.
that's a big bummer Troy. Hopefully once they're rebuilt they'll be bulletproof!
Lance
TLCA Member
2003 4Runner SR5 4x4 Chaos Edition
2000 Toyota Landcruiser
19xx M416 Trailer
Chaos Edition Profile
Operation Rebuilding Chaos Edition
01001001001001110110110100100000011000010010000001 11011101100101011000100111011101101000011001010110 010101101100011001010111001000100001
I just finished rebuilding the rear shocks. First up there are metal shavings in the fluid. it looks to have all come from the machined aluminum parts. I found one burr still attached to the piston. Again this points to them being thrown together as fast as possible.
From a design standpoint the piston was really well made. Alot of the shocks out there dont support the valve stacks very well and they can bend or break a valve. FOA has a nicely built one so long as you take the burrs and aluminum chips off it before install.
internal parts are in a state of change. The wear band I have is different then the wear bands that came in the seal kit. I assume they are interchangeable but the new one will actually seal better. The wear band in my shocks will allow fluid to pass by and I attribute the .020 compression valving I have is to make up for that. I did however get the new style end caps with double o-ring seals. Alot of shocks out there only have one o-ring so that was a nice surprise. I'd guess they do this more to increase there odds of it sealing then to have a redundant seal, but its nice just the same.
oh and on my first try I built two shocks that don't leak and filled them with the correct amount of fluid (they extend all the way on their own). I now have zero sympathy for the poor assembly of FOA shocks from the factory.
Also get a nitrogen tank if you get these types of shocks. I cant tell you how many times I have used it now. These types of shocks are impossible to install/remove while charged. I also used the nitrogen to pop off the end caps rather then wrestle with them.
Last edited by troyboy162; 10-07-2014 at 01:09 PM.
Glad you ended up with some quality parts and assembly, even if half that is your doing.
2005 Lexus LX470 - Stock for now...
1998 Toyota 4Runner SR5 V6 4x4 + a bunch of goodies. Lifted, Locked, Illuminated and Armored. Winner,"Best Offroad Truck" - 2010 Pismo Jamboree. It's been upside down and still drives me to work.