eventually. Still don't even know if we're going with a log cabin or underground concrete/rebar home. Might even just get water/septic/electric and take the RV down there if it's supposed to be a mild winter . . .
eventually. Still don't even know if we're going with a log cabin or underground concrete/rebar home. Might even just get water/septic/electric and take the RV down there if it's supposed to be a mild winter . . .
Keith '88 4runner SR5 Garage Thread
Well its no PA, but it is nice down there.
Too bad your gears can't fit in my diffs, after you go to 4.88 I wouldn't mind going 4.56 myself
Avdian (Avy, Avi, Av, Eddie are some nicknames)
Tess - 97' 4Runner "Project Something Or Another" - No More
Annabelle - 00' 4Runner Limited "The Next Chapter"
Natascha - 99' GTI 2.0 N/A Auto - SOLD!!
Swordfish - 05' Camry 2.4 Auto
Project Fluffy - 93' SC400
The front no, the gears from my V6 rear 3rd should fit in an elocker, but they also have unknown mileage and would have to be set-up with the same exact contact pattern - probably better to spend the $ on a new gear set + solid collar.Originally Posted by YotaFun
Keith '88 4runner SR5 Garage Thread
Yeah I figured as much, for now I haver other priorities, the 4.30s will have to sufice.
Avdian (Avy, Avi, Av, Eddie are some nicknames)
Tess - 97' 4Runner "Project Something Or Another" - No More
Annabelle - 00' 4Runner Limited "The Next Chapter"
Natascha - 99' GTI 2.0 N/A Auto - SOLD!!
Swordfish - 05' Camry 2.4 Auto
Project Fluffy - 93' SC400
One last pic of the actuator all finished, tested and ready to go
Yukon 4.88 gears with a solid pinion collar are next on the list
Keith '88 4runner SR5 Garage Thread
Reviving this thread.
How hard would you say this was to do?
I figured out my motor solenoid is good, but I think the actual gear section is seized.
Would I be able to take it apart and clean it out and hopefully it will work, or should I look for a motor to source parts?
Avdian (Avy, Avi, Av, Eddie are some nicknames)
Tess - 97' 4Runner "Project Something Or Another" - No More
Annabelle - 00' 4Runner Limited "The Next Chapter"
Natascha - 99' GTI 2.0 N/A Auto - SOLD!!
Swordfish - 05' Camry 2.4 Auto
Project Fluffy - 93' SC400
Wasn't too difficult - stick a boat drain plug or a rubber "universal oil drain plug" in while the motor it's off to keep it clean inside. Besides, taking it apart to lube and clean (wire wheel everything EXCEPT the plastic gear) is relatively free. Just be gentle taking the cast alum plate off to get to the guts.
Do you have the single spring, fine mesh gear or the double spring gear? I have spare double spring stuff if you need any parts
Keith '88 4runner SR5 Garage Thread
If your in need of an e-locker motor assy, let me know.....I've got 3 broken 3rd members sitting in my garage with them.
99 SR5 4Runner Highlander 5spd V6 4WD e-locker<br />Myspace<br />3rd Gen Bumper Build-up<br />1GR-FE 4.0L V-6 & RA60F 6-speed for my project vehicle<br /><br /><br />Don't Ask when I'm gonna go SAS, I'm not... I'll build a buggy first!
I haven't gotten to it yet but thats for the tips.Originally Posted by corax
I might take you up on that actually Bruce, I presume one of the three works lol!Originally Posted by BruceTS
I figure have one lying around just in case I screw something up, and If I do get it fixed I can ship it back to you so you have it for the diff
Avdian (Avy, Avi, Av, Eddie are some nicknames)
Tess - 97' 4Runner "Project Something Or Another" - No More
Annabelle - 00' 4Runner Limited "The Next Chapter"
Natascha - 99' GTI 2.0 N/A Auto - SOLD!!
Swordfish - 05' Camry 2.4 Auto
Project Fluffy - 93' SC400
Got the motor yesterday Bruce.
and I have to say YOU RULE!!!
having a selectable locker is awesome!!!!
Avdian (Avy, Avi, Av, Eddie are some nicknames)
Tess - 97' 4Runner "Project Something Or Another" - No More
Annabelle - 00' 4Runner Limited "The Next Chapter"
Natascha - 99' GTI 2.0 N/A Auto - SOLD!!
Swordfish - 05' Camry 2.4 Auto
Project Fluffy - 93' SC400